HHB comm PERSONAL COMPACT DISC RECORDER CDR 830 User Manual download pdf (Page 46)

BurnIT CDR830 COMPACT DISC RECORDER

1. Insert a recordable disc (CD-R or CD-RW)

2. Use the INPUT SELECTOR to select either the OPTICAL or COAX digital input depending on how you

have connected the source machine to your CDR830.

3. If necessary adjust the DIGITAL RECORD LEVEL by accessing D.VOL in the MENU (Function 5).

PLEASE NOTE THAT MOST COMMERCIAL RECORDINGS ARE OPTIMIZED FOR LEVEL AND SO IT IS

NOT NECESSARY TO ADJUST DIGITAL RECORD LEVEL. Use this control when the signal level is too

low or when you want to equalise the level of several tracks.

4. Start the recording manually by pressing RECORD. The CDR830 will first display the type of

machine connected to the input (e.g. DAT, CD, MD,) and then display the sample rate of the

source material (32, 44.1, 48K). The machine will then flash SET-UP in the display whilst it is

performing its Optimum Power Calibration (OPC). Once set-up has stopped flashing, press the PLAY

button to start recording. Press STOP to finish the recording.

• Start the recording automatically using SYNCHRO.

• Ensure that the source material is not playing otherwise CHECK INPUT? will appear in the display.

• Press SYNCHRO to select SYNC-1 which automatically copies 1 track (useful for compilations).

• Press SYNCHRO again to select SYNC-ALL which is used to copy all tracks automatically.

• Press SYNCHRO again to select SYNC-FINAL which is the same as SYNC-ALL except that the disc

will, in addition, be finalized automatically about 1 minute after recording has finished. Press STOP

at any time to manually terminate the recording.

When recording finishes, the display will show PMA REC whilst the Programme Memory Area is

written. DO NOT DISTURB OR SWITCH OFF THE MACHINE DURING THIS PROCESS.

•

The CDR830 employs an intelligent track numbering scheme which adapts to the type of signal being

recorded. It is also used to determine how the machine starts automatically in SYNCHRO mode.

•

The following table shows how this scheme works.

HOW TO RECORD USING DIGITAL INPUTS

TRACK NUMBERING IN SYNCHRO & NORMAL MODES

1. Insert a recordable disc (CD-R or CD-RW)

2. Use the INPUT SELECTOR to select the analogue input.

3. Adjust the record level using the ANALOG REC LEVEL control preferably so that the signal peaks as

close to '0' dBFS without going 'OVER'.

4. Start the recording manually by first pressing RECORD. The CDR830 will first display ANALOG and

will then flash SET-UP in the display whilst it is performing OPC. Once set-up has stopped flashing,

press the PLAY button to start recording. Press STOP to finish the recording.

• Start the recording automatically using SYNCHRO.

• Ensure that the source material is not playing otherwise CHECK INPUT? will appear in the display.

• Press SYNCHRO to select SYNC-1 which automatically copies 1 track (useful for compilations).

• Press SYNCHRO again to select SYNC-ALL which is used to copy all tracks automatically.

• Press SYNCHRO again to select SYNC-FINAL which is the same as SYNC-ALL except that the disc

will, in addition, be finalized automatically about 1 minute after recording has finished. Press STOP

at any time to manually terminate the recording.

When recording finishes, the display will show PMA REC whilst the Programme Memory Area is

written. DO NOT DISTURB OR SWITCH OFF THE MACHINE DURING THIS PROCESS.

HOW TO RECORD USING ANALOGUE INPUTS

MODE AUTO/MANUAL TRACK INCREMENT METHODSTART METHODINPUT

SYNCHRO AUTO CD, MD Sub-codeLevel > -90dBFS

CD & MD

[spdif]

SYNCHRO AUTO DAT START IDDAT START ID

DAT

[spdif]

SYNCHRO AUTO LEVEL Threshold [A.LVL in MENU]Level > A.LVL in MENUANALOGUE

SYNCHRO MANUAL NoneLevel > -90dBFS

CD & MD

[spdif]

SYNCHRO MANUAL NoneDAT START ID

DAT

[spdif]

SYNCHRO MANUAL NoneLevel > A.LVL in MENUANALOGUE

NORMAL AUTO CD, MD Sub-codeManual

CD & MD

[spdif]

NORMAL AUTO DAT START IDManual

DAT

[spdif]

NORMAL AUTO LEVEL Threshold [A.LVL in MENU]ManualANALOGUE

NORMAL MANUAL NoneManual

CD & MD

[spdif]

NORMAL MANUAL NoneManual

DAT

[spdif]

NORMAL MANUAL NoneManualANALOGUE

1.Insert a recorded disc and press PLAY. The display will show the 4 symbol.

2.Use the 7 and 8 to rewind and fast forward respectively.

3.Turn the DIGITAL RECORD LEVEL, 9: during playback to skip backwards or forwards to a different

track.

4.Use the supplied remote control to start playback from a particular INDEX number (see operations

manual).

HOW TO PLAY BACK

•

In SYNCHRO recording mode, if the source is 16-bit, recording will automatically stop if the level falls below

-96dBFS for 5 seconds or more.

•

If the source is 24-bit, recording will automatically stop when the level falls below -90dBFS for 5 seconds

or more. This is due to the built in dithering circuitry of the CDR830.

AUTO-STOP FUNCTION

1. There are 5 Erase modes for CD-RW; ERASE TOC (Un-finalizes a CD-RW)

ERASE LAST (Erases last track)

ERASE ALL (Erases all tracks)

ERASE RANGE (Erases a range of tracks)

INITIALIZE (see page 38 of the operations manual)

2. Press ERASE, then use 9 : to select the required erase mode.

3. Press PLAY.

HOW TO ERASE (CD-RW ONLY)

CDR830.QXD 16/11/00 10:51 Page 2

1 2 ... 41 42 43 44 45 46 47 48 49 50

Comments to this Manuals

No comments

HHB comm PERSONAL COMPACT DISC RECORDER CDR 830 User Manual Page 46

Comments to this Manuals

Related products and manuals for CD players HHB comm PERSONAL COMPACT DISC RECORDER CDR 830